Xloader version: Built: Mon Feb 25 03:45:32 PM 2013 Configured for: 8500 B0 Running on chip ID: 8500B2 SECURITY_Init Boot scenario: NORMAL USB - Enabled: 0x1 Enum done: 0x0 Last reset reason: POWER_ON_RESET XP70_DATA_MBFFC: 0xFF000001 PWR_MNGT_STARTED 1 Probing for eMMC on SDI2 About to load MEMINIT After MEMINIT loaded verify_signedheader verify_signedheader done verify_payload hdr size: 0xD0 payload 0x40026244 About to exec MEMINIT function SoC settings: INFO: @(#)SOC-SETTINGS v1.0.3 Vape100+50mV Vape50+25mV db8520 1000Mhz Feb 25 2013 15:45:37 SoC settings: INFO: Vbat check 0x00000253 SoC settings: INFO: AB8505 V2 detected SoC settings: INFO: Vendor ID = 0x00000001, CS0 density = 0x00000018, CS1 density = 0x00000018 SoC settings: INFO: CS0 revision ID1 = 0x00000001, CS0 revision ID2 = 0x00000000 SoC settings: INFO: CS1 revision ID1 = 0x00000001, CS1 revision ID2 = 0x00000000 SoC settings: INFO: AVS Enable, FVR21 value = : 0x871917ed, FVR22 value = : 0x0023dce1 SoC settings: INFO: Memory size=0x40000000 (1024 MB), CS0 (512 MB) CS1 (512 MB) SoC settings: INFO: DDR Test Ended successfully. SoC settings: INFO: Requesting MAX OPP from PRCMU SoC settings: INFO: Set MAX OPP OK SoC settings: INFO: vmin = above 1.35V, vbbp = -100mV, vbbn = -100mV SoC settings: INFO: Very Fast Parts [>......](Very Fast for N Transistor, Very Fast for P transistor) MEMINIT passed OK About to load NORMAL After NORMAL loaded verify_signedheader verify_signedheader done verify_payload hdr size: 0xD0 payload 0x141080D0 XL_DisableCachesMmu Before ENABLE_L2CC After ENABLE_L2CC Before call normal [ 0.0000] init_microusb_pmic: Turn on reason 0x02 [ 0.0000] init_microusb_pmic: Turning on due to cable plug? 0 [ 0.0049] init_ab8500_gpadc: ADC_INPUT_BTEMP.gain : 1336 [ 0.0102] init_ab8500_gpadc: ADC_INPUT_BTEMP.offset : 1408 [ 0.0158] [hw_board] dram_init(712): dram_init [ 0.0202] [hw_board] dram_init(779): Ram_Info.total_size = 1024MB [ 0.0467] Samsung S-Boot 4.0 [ 0.0467] Copyright (C) 2012 System S/W Group. Samsung Electronics Co., Ltd. [ 0.0511] Board: SKOMER ID 264 / built on DELL215 on Feb 25 2013 15:39:39 [ 0.0580] CPU: DB8500 (ID=0x9001dbf4) [ 0.0619] [main] init_param_status(351): [ 0.0659] [main] Re_partition(225): booting code=0xc0c0c0c0 [ 0.0866] [hsmmc_init] MMC card is detected [ 0.0880] Product Name : M4G1YC [ 0.0883] CID:1501004d 34473159 43013bff 46d6800a [ 0.0968] ext_csd [ 0.1289] Total Card Size: 3776 MByte [ 0.1290] Total Sector Count: 7733248 [ 0.1405] MoviNand Initialization Complete! [ 0.1405] checking whether toc is redirected [ 0.1659] [pit] pit_update_partition(278): Board partition updated. [ 0.1776] [gpt] check_protective_mbr(230): read protective mbr [ 0.1778] [main] loke_init(255): j4fs_open.. [ 0.7469] [main] loke_init(257): success [ 0.8565] [param_block] load_lfs_parameters(375): valid magic code and version. [ 0.8581] [main] loke_init(265): Board id 264 [ 0.8732] [ddi] init_ddi_data(74): usable ddi data. [ 0.8935] [FG] VCELL ADC = 589, VOLTAGE = 3743mV [ 0.8935] musb_init : SKOMER : High-Speed USB OTG Controller [ 0.8986] [CHG] cable type:0x4000, status:0x0 [ 0.9025] [CHG] Skip to initialize charger [ 0.9066] [CHG] OVP REG SETTING : 0x44 [ 0.9211] reading nps status file is successfully!. [ 0.9211] nps status=0x504d4f43 [ 0.9238] [hw_board] board_process_platform(950): check_power_key [ 0.9296] check_power_key: Ponkey_1 Pressed. Reset status 1 [ 0.9351] check_power_key: No rising edge, Booting .... [ 0.9904] [read_switch_off_status] SwitchOff_Status 0x1 [ 0.9915] [abx500_rtc_get_time] RTC= 0xb:0x92:0xe:0x0:0x0 [ 0.9954] [hw_board] check_reboot(868): reset_state: 0x 0 [ 1.0010] [hw_board] check_reboot(877): softreset_state: 0x 0 [ 1.0069] [read_turnon_state] TurnOn_Status 0x0 [ 1.0115] [hw_board] check_reboot(880): turnon_state: 0x 0 [ 1.0174] hw_pm_status: chg_status = 0 reboot_reason = 0x0 [ 1.0226] [FG] __BATT_CAPACITY :0xffffffff [ 1.0267] [hw_board] board_process_platform(1027): booting_mode: 0x0 [ 1.0534] [FG] VCELL ADC = 621, VOLTAGE = 3822mV [ 1.2667] Probe HW [ 1.2828] MCDE HW revision 0x03000800 [ 1.2828] db8500 V2 HW [ 1.2832] mcde_probe: EXIT 0 [ 1.2860] dsilink_init: Probing dsilink device[0] [ 1.2907] dsio[0]: 0xa0351000 [ 1.2937] hw revision 0x02327457 [ 1.2969] nova_dsilink_v2_init: initiated [ 1.3009] dsilink_init: Probing dsilink device[1] [ 1.3056] dsio[1]: 0xa0352000 [ 1.3085] hw revision 0x02327457 [ 1.3118] nova_dsilink_v2_init: initiated [ 1.3157] dsilink_init: Probing dsilink device[2] [ 1.3204] dsio[2]: 0xa0353000 [ 1.3234] hw revision 0x02327457 [ 1.3266] nova_dsilink_v2_init: initiated [ 1.3306] skomer_display_probe function entered [ 1.4952] dsi_read_panel_id: Read device id of the display [ 1.4953] clk_set_rate: f=349440000 [ 1.4985] ui value 11 dsi_hs_freq 349 in MHz [ 1.5028] nova_dsilink_enable link enabled [ 1.5069] mcde_dsi_dcs_read failed to read display ID [ 1.5119] link disabled [ 1.5144] mcde_ovly_apply: ovly->dirty or ovly->dirty_buf! [ 1.5198] mcde_ovly_apply: ovly->dirty or ovly->dirty_buf! [ 1.5253] nt35510_set_power_mode: power_mode = 1 [ 1.6900] clk_set_rate: f=349440000 [ 1.6900] ui value 11 dsi_hs_freq 349 in MHz [ 1.6921] nova_dsilink_enable link enabled [ 1.8184] num_ovl 1 [ 1.8184] ovly0 pfwml:240 32bpp [ 1.8184] num_ovl 1 [ 1.8201] Software TRIG on channel 0 [ 1.8236] nt35510_set_power_mode: power_mode = 2 [ 2.0086] Overlay updated, chnl=0 [ 2.0286] Software TRIG on channel 0 [ 2.0786] Overlay updated, chnl=0 [ 2.0986] nt35510_set_power_mode: power_mode = 2 [ 2.0987] Autoboot (0 seconds) in progress, press any key to stop Autoboot aborted.. [ 2.1055] SBL> SBL> SBL>